APS Rotated Mount Turbocharger Inlet Pipe/Cold Air Intakes
 

   
 
 

APS Rotated Mount Turbocharger Turbocharger Inlet Pipe - APSWRX-HFA/R9
Item No. Part No. Description Qty.
1 990-029-150 ELEMENT - Air Cleaner 1
2 995-022-900 DUCT - Air Inlet 1
3 995-022-250 SLEEVE - MAF 1
4 995-032-000 BRACKET - Air Inlet Duct Mounting 1
5 000-002-100 BOLT - Hex 6mm x 1.0 x 14 mm (SEMS) 2
6 995-222-990 HOSE - Silicone - Compressor Entry 1
7 000-930 CLAMP - Hose 90mm - 110mm 1
8 000-929 CLAMP - Hose 80/100mm 1
9 995-855-300 HOSE - Moulded BOV 1
10 000-903 CLAMP - Hose 25/40mm 4
11 000-587 BARB - 90°- 3/8" x 1/2" Hose 1
12 000-509 BARB - ST. - 1/4" x 5/16" Hose 1
13 000-663 ADAPTOR - 90° - 1/4"BSPM x 1/4"BSPF 1
14 000-838-055 HOSE - Emissions - 8mm I.D. x 550mm 1
15 995-994-000 HOSE - Breather - 12mm I.D. x 650mm 1
16 000-151 GRUB SCREW - 6mm x 1.0 x 8mm 3
17 995-855-400 HOSE - By-Pass Valve 32mm I.D. x 60mm 1
18 000-911 SPRING CLIP - 12.5mm 7
19 000-541 TEE PIECE - 5/16" Barb 1
20 000-911-017 SPRING CLIP - 17 4
21 000-948 TEE PIECE - 12.5mm (Plastic) 1
22 995-102-000 ADAPTOR - PCV 1
23 000-987-178 CABLE TIE - 178cm 1
24 000-909 CLAMP - 9mm 80/100 HOSE 1
25 000-911-014 SPRING CLIP - 5/16" HOSE 1

1

 Remove the cold air intake duct.

2

 Remove the air filter box.

3

 Remove the air intake resonator and retain the stock mounting nuts.

4

 Install the barb (Item 11), 90 deg adaptor (Item 13) and the 90 deg barb (Item 12) to the inlet duct (Item 2).

5

 Install the MAF sensor to the inlet duct (Item 2).

6

 Insert the inlet duct (Item 2) through the inner fender using a rotating motion as shown.

7

 Install the compressor entry hose (Item 6) onto the inlet duct (Item 2) and then on to the turbocharger compressor entry.

Do not tighten the hose clamps yet.

8

 Install the inlet duct mounting bracket (Item 4) and retain with the stock nuts and hex bolts (Item 5).

9

 Tighten the hose clamps on the compressor entry hose (Item 6).

10

 Install the blow off valve hose (Item 9), bypass hose (Item 17) and install the blow off valve.

Tighten the hose clamps.

11

 Install the air filter element (Item 1) and retain with a hose clamp.

12

 Install the breather hose (Item 15) and retain with spring clips.

Cut a 4" length of hose from the emission hose (Item 14) and install as shown.

Install the emission hose and retain with spring clips.

13

 Note US specification STI uses the PCV adaptor (Item 22) and cable tie (Item 23).

14

 Overall view of completed installation.